Do you know how to solve the problem of water leakage in plastic inspection wells?

目前塑料检查井已经广泛应用于雨污水排水系统中，但是施工中经常会遇到这样那样的问题，有些是产品的问题，有些是施工的问题，多种多样。下面我们粗略的阐述下最常见的问题——漏水问题。

At present, plastic inspection wells have been widely used in rain and sewage drainage system, but construction often encounter such problems, some are product problems, some are construction problems, a variety of. Now let's sketch the most common problem -- water leakage.

塑料检查井遇到最大的问题就是连接后接口漏水。塑料检查井在安装之前一般厂家或销售商都会根据施工现场选用的管道搭配合适的橡胶密封圈。但是很多时候往往不能做到彻底地闭水。可能产生漏水的原因很多种，下面大致罗列下。

The biggest problem with the plastic inspection well is the leakage after the connection. Plastic inspection wells in the installation before the general manufacturers or vendors will be selected according to the construction site of the pipeline with the appropriate rubber sealing ring. But often, we can not completely shut the water. There may be many reasons for possible leakage.

一、胶圈没有配好，没能做到正真的闭水。

1. The apron is not properly matched, and it can not really shut down the water.

二、选用的产品不稳定，管道、塑料检查井都是塑料制品，塑料有收缩率，可能每批的产品都有一定的误差，现场施工时可能出现开始安装能闭水，之后施工就产生漏水现象。避免这种情况的发生首先要选择优质的产品，降低产品产生误差率的概率。其次及时的发现问题，更换合适的橡胶圈。

Second, the selected products are unstable, pipelines, plastic inspection wells are plastic products, plastic shrinkage, each batch of products may have a certain error, the site construction may start to install the water can be closed, then the construction will produce leakage phenomenon. To avoid such a situation, we must first select quality products and reduce the probability of error rate. Secondly, find out the problems in time and replace the suitable rubber rings.

三、施工时，橡胶圈固定不到位，甚至出现橡胶圈翻转的现象。所以说规范的施工是保证工程质量的前提。

Three. During construction, the rubber ring is not fixed enough, or even the rubber ring is turned over. Therefore, the standard construction is the premise to ensure the quality of the project.

四、产品在运输过程中产生变形。变形不太厉害的时候，安装的时候能稍微弥补下，但是严重的话就很难做到不漏水了，可以适当的调换产品，以保证工程的质量。

Four, product deformation during transportation. When the deformation is not too severe, the installation can make up for it slightly, but if it is serious, it is very difficult not to leak. The product can be properly replaced to ensure the quality of the project.

漏水是塑料检查井在施工时遇到最多，也是最头疼的问题.江苏正林环保科技有限公司在塑料检查井的销售中积累了丰富的经验，橡胶圈的配置全面，在所做工程中能够做到很好的闭水效果，得到广大用户的一致好评。

Leakage is the most common and headache problem encountered in the construction of plastic inspection wells. Jiangsu Zhenglin Environmental Protection Technology Co., Ltd. has accumulated rich experience in the sales of plastic inspection wells. Rubber rings are fully equipped, which can achieve good water shut-off effect in the project, and has been praised by the majority of users.